Granite Guru
Join Date: May 2010
Location: Raleigh, NC
Age: 54
Posts: 197
Feedback: 0 reviews
|
|
LinkBack | Thread Tools | Display Modes |
Anyone have and easy fix for cutting this corner off...
|
Should the "corner" even be a concern as far as cutting my rear tire. Should I just cut the corner and spray some paint on it? Thanks in advance for and advice or directing me to the solution. Maybe rock rails would protect it...don't know
Thanks
Thanks
Last edited by loanwolf2005; 08-06-2010 at 06:35 PM.
| Sponsored Links | |||
|
Advertisement |
|
||
JKO Addict!
Join Date: Nov 2009
Location: Tracy, California
Age: 39
Posts: 3,068
Feedback: 4 reviews
Sawzall and some spray paint, thats what I did with mine.
United States Army 1997-Present
When a life or death decision must be made in seconds.....the police are only a minute away.
Rock God
Join Date: Jun 2010
Location: North Little Rock, Arkansas
Age: 44
Posts: 985
Feedback: 0 reviews
I used my dremel + spraypaint, and only trimmed my pinch weld back about an inch or so at a 45 degree angle. At full stuff, it was still rubbing a little on my tires.
A buddy of mine cut his waaaaay back, filled the hole with JB Weld, and painted. Looked good.
But ya, I'd do something about it if you're running larger tires.
A buddy of mine cut his waaaaay back, filled the hole with JB Weld, and painted. Looked good.
But ya, I'd do something about it if you're running larger tires.
| Sponsored Links | |||
|
Advertisement |
|
||
JKO Addict!
Join Date: May 2009
Location: Denton, TX
Posts: 13,230
Feedback: 1 reviews
BFH and bent mine.
SOLD - '09 2dr Rubicon - 1.0Gal | 6spd | 37s | 4.88s |
To view links or images in signatures your post count must be 10 or greater. You currently have 0 posts.
| OR-Fab cage | Poly Cage | BFH Front | XRC Rear | XRC12 Winch | Walker Evans Beadlocks |
Retired from the Jeep community, for now.
To view links or images in signatures your post count must be 10 or greater. You currently have 0 posts.
Heat'n and a beat'n...
Join Date: Jan 2009
Location: South Louisiana
Posts: 3,954
Feedback: 0 reviews
I used a grinder and a cutting wheel, then filled the small void with some caulking or foam, and painted it.
corey d
corey d
corey d
2008 JEEP...
Granite Guru
"Jezebel"
x2 worked fine
My sig is HUGE in Japan
Granite Guru
Join Date: May 2010
Location: Raleigh, NC
Age: 54
Posts: 197
Feedback: 0 reviews
JKO Addict!
The Beast
Big Fucking Hammer 
i cut mine with a sawzall.. measured 2-3" up and 2-3" over and cut diagonally and hit it with flat black. 2 years and running no rust and no cuts.
oh and here is a whole thread dedicated to this... https://www.jkowners.com/forum/showth...ght=pinch+seam
i cut mine with a sawzall.. measured 2-3" up and 2-3" over and cut diagonally and hit it with flat black. 2 years and running no rust and no cuts.
oh and here is a whole thread dedicated to this... https://www.jkowners.com/forum/showth...ght=pinch+seam
Remember to support our great Vendors here at JKO when purchasing your Jeep goods!
To view links or images in signatures your post count must be 10 or greater. You currently have 0 posts.
To view links or images in signatures your post count must be 10 or greater. You currently have 0 posts.
Last edited by .:eMETAL:.; 06-27-2010 at 07:45 PM.
Rock God
Join Date: Jul 2009
Location: Austin, TX
Age: 38
Posts: 1,003
Feedback: 0 reviews
Now that I have my sawzall....
08 Unlimited - Flame Red "Lucy"
2.5" RC Coils & 33" KM2 on stockers
08 JK - Stone White "The Goat"
2.5" BB, 35" MTRs on 15s, Rubi sliders - just the beginning
To view links or images in signatures your post count must be 10 or greater. You currently have 0 posts.
Keeping Austin Weird
Official Monkey Business
My Jeep
With the suspension that I have I didn't have to trim the pinch. At full flex its close but does not contact the 37" KM2
08 2Door Red Rubicon. Rock Krawler 5.5 Longarm Coilover, Polly rear Coilovers. AEV hood & wheels, 37"KM2s, JE Reel 1350 shafts, 5.38 Yukon gears, Superior axles, Shrockworks stubby, Fab Fours rear, sPod, Rebel Offroad brakes, Warn winch and lots more.
To view links or images in signatures your post count must be 10 or greater. You currently have 0 posts.
To view links or images in signatures your post count must be 10 or greater. You currently have 0 posts.
| Sponsored Links | |||
|
Advertisement |
|
||
«
Previous Thread
|
Next Thread
»
| Thread Tools | |
|
Show Printable Version Show Printable Version
Email this Page Email this Page
|
|
| Display Modes | |
|
|
| Posting Rules | |
