New Tail Gate Plates from Desert Snake - Page 4

DesertSnake · 05-03-2011, 06:45 AM

Quote:

Originally Posted by jvandy50

do you know how far the bracket sticks out? or better yet if it'll fit between the tailgate plate and a smittybilt xrc tire carrier?

We don't know anybody locally that have that Tire Carrier.

If you want, try to look behind your tire carrier and see if the upper tailgate holes clear the tire carrier tubes (Send pictures if you can). I think, we could make something custom for you that anybody else could benefit from it.

JKCobra · 05-03-2011, 03:30 PM

Any chance of either a calico jack pirate or the full cobra symbol plate?

DesertSnake · 05-04-2011, 09:50 AM

Quote:

Originally Posted by JKCobra

Any chance of either a calico jack pirate or the full cobra symbol plate?

With a a few mods, it is possible; I like them, both. Keep in mind, these are cut out, not floating metal is possible.

Which would you prefer?

DesertSnake · 05-04-2011, 10:58 AM

All,

Here is the new CB antenna bracket design. It will allow you to mount CB antenna and aux light (Optional. if you don't have anything that would interefere on the back of your rig). It would be posible to use it on any corner tail gate's bolt pattern

JKCobra · 05-04-2011, 11:29 AM

Quote:

Originally Posted by DesertSnake

With a a few mods, it is possible; I like them, both. Keep in mind, these are cut out, not floating metal is possible.

Which would you prefer?

I am leaning towards the cobra symbol, mainly bc i'm not sure what the skull would look like with the floating eyes and nose. I know you would have to support them somehow and that might ruin the look. Any thoughts?

The other option I also considered was the following, but I wasn't certain if y'all can do school logos:

rballman · 05-04-2011, 08:21 PM

whoop!

kabookie10 · 05-05-2011, 09:07 AM

Quote:

Originally Posted by JKCobra

I am leaning towards the cobra symbol, mainly bc i'm not sure what the skull would look like with the floating eyes and nose. I know you would have to support them somehow and that might ruin the look. Any thoughts?

The other option I also considered was the following, but I wasn't certain if y'all can do school logos:

If you guys can do schools logo's i'd be interested in the Ohio State logo.

bnb2010 · 05-08-2011, 12:25 PM

I like the calico jack or jolly Roger. Also like the antenna mount

Sent from my smoke signals

BADGER · 05-09-2011, 01:42 PM

Nice product and I like the CB antenna mount.

Now, at the risk of being mundane and practical....any chance of a license plate mount or holes for a license plate?

Hemo · 05-09-2011, 01:54 PM

Got my JKO Plate in and it looks GREAT. I've painted the screen mesh Detonator Yellow so it matches my Jeep. At least for the short term I know I am running a one of a kind Tailgate Plate!

Thanks Desert Snake

.

DesertSnake · 05-09-2011, 03:06 PM

We would love to see pics of the plate on your rig

Quote:

Originally Posted by Hemo

Got my JKO Plate in and it looks GREAT. I've painted the screen mesh Detonator Yellow so it matches my Jeep. At least for the short term I know I am running a one of a kind Tailgate Plate!

Thanks Desert Snake

.

Muvovr · 05-09-2011, 03:31 PM

Quote:

Originally Posted by JKCobra

I am leaning towards the cobra symbol, mainly bc i'm not sure what the skull would look like with the floating eyes and nose. I know you would have to support them somehow and that might ruin the look. Any thoughts?

The other option I also considered was the following, but I wasn't certain if y'all can do school logos:

GiG'EM !!!

DesertSnake · 05-09-2011, 04:49 PM

Some like this?

Quote:

Originally Posted by X-Defector

Nice product and I like the CB antenna mount.

Now, at the risk of being mundane and practical....any chance of a license plate mount or holes for a license plate?

DesertSnake · 05-10-2011, 08:54 AM

We can make almost any design, the problem is the copyright.

Our lawyer has advised us to refrain from coying or transferring any registered logo into any of our products.

Because we don't like to say no with out another option, we could make a flat plate where you would be able to place any school decal. Moreover, we could create another layer on top of the plate with the sticker layout for a 3D effect.

All these requests will be custom orders.

Cenair

Quote:

Originally Posted by JKCobra

I am leaning towards the cobra symbol, mainly bc i'm not sure what the skull would look like with the floating eyes and nose. I know you would have to support them somehow and that might ruin the look. Any thoughts?

The other option I also considered was the following, but I wasn't certain if y'all can do school logos:

JKCobra · 05-10-2011, 12:20 PM

Not sure I follow what you mean with the 2nd layer? Do you have a visual example?

Quote:

Originally Posted by DesertSnake

We can make almost any design, the problem is the copyright.

Our lawyer has advised us to refrain from coying or transferring any registered logo into any of our products.

Because we don't like to say no with out another option, we could make a flat plate where you would be able to place any school decal. Moreover, we could create another layer on top of the plate with the sticker layout for a 3D effect.

All these requests will be custom orders.

Cenair

Muvovr · 05-10-2011, 12:57 PM

I think he is talking about making the outside perimeter of the decal a plate to achieve the 3-D look over his flat plate design ...

?????

DesertSnake · 05-10-2011, 02:59 PM

That would be correct

Thanks for clarifying

Quote:

Originally Posted by Muvovr

I think he is talking about making the outside perimeter of the decal a plate to achieve the 3-D look over his flat plate design ...

?????

yellow rubicon · 05-10-2011, 04:33 PM

Can you do one in stainless stell?
2nd question:how come I can't open your website?
3rd question:are you planing on making a 3rd brake light bracket that attaches to the plate?
some advice:you should have the option of a rubber liner that goes between
the plate and the tailgate,kind like poison spyder with the side armor that thing saved my body(geniuses)
thanks

DesertSnake · 05-10-2011, 06:46 PM

Answers:

Quote:

Originally Posted by yellow rubicon

Can you do one in stainless stell?

A: No at this time

Quote:

Originally Posted by yellow rubicon

2nd question:how come I can't open your website?

A: The website is up, but it doesn't have all the new products yet. Our web master is completing a new version (not available yet).

Quote:

Originally Posted by yellow rubicon

3rd question:are you planing on making a 3rd brake light bracket that attaches to the plate?

A: We will make one, but not in the near future.

Quote:

Originally Posted by yellow rubicon

some advice:you should have the option of a rubber liner that goes between
the plate and the tailgate,kind like poison spyder with the side armor that thing saved my body

A: Our plates come standard with rubber strips to separate the plate from the tail gate, this way we avoid scratching the paint on the tail gate.

I hope this answers your questions boss

Cenair

yellow rubicon · 05-11-2011, 09:51 AM

thanks a lot for the infos,you'll ear from me soon and will be for my order.

DesertSnake · 05-11-2011, 08:36 PM

Quick update

For those who will be @ Jeep beach 2011 in Daytona, we will display the final version of the double Jerry can carrier, plus a single jerry can version.

Follow the thread here:
http://jkowners.com/forum/showthread...071#post774071

CB / Light bracket will be on display as well

PS: We will also be introducing our new line JK front and rear bumper prototypes

yellow rubicon · 05-12-2011, 12:19 PM

I would like to see some drawing of your future bumpers,and I think I'm not the only one.
pleaaaaase!!

DesertSnake · 05-12-2011, 12:34 PM

Quote:

Originally Posted by yellow rubicon

I would like to see some drawing of your future bumpers,and I think I'm not the only one.
pleaaaaase!!

Sneak pic only for you

These are prototypes

We were able to sink the Powerplant a few inches down, between the frame rails, for better airflow to the engine. We won't sell the light bar, it is a pain to make

On this one, our logo will be replaced by a design to incorporate LEDs

yellow rubicon · 05-12-2011, 06:26 PM

what an honor pictures just for me!!

just kidding,very well done!I like them both;about the light bar I'm a steel fabricator(stainless and aluminum)I understand those compound miter on square tubing are bitches.
So when the front bumper will be available "just for me",and what the price range is gonna be?
and how much is gonna weight+/-?
sorry I ask to many questions!
THANKS A LOT.

jvandy50 · 05-12-2011, 08:47 PM

i actually like the name in the rear bumper

05-04-2011, 10:58 AM	#79
DesertSnake JKowners Vendor Join Date: Mar 2011 Member # 14438 Location: Tampa, Florida Posts: 164 Feedback: 1 reviews	CB Antenna + Light Bracket Design All, Here is the new CB antenna bracket design. It will allow you to mount CB antenna and aux light (Optional. if you don't have anything that would interefere on the back of your rig). It would be posible to use it on any corner tail gate's bolt pattern __________________ Desert Snake http://www.DesertSnakeOffroad.com http://www.facebook.com/DesertSnakeOffroad

05-04-2011, 08:21 PM	#81
rballman JKowners Vendor Join Date: Feb 2010 Member # 8265 Location: Durango, CO Age: 31 Posts: 505 Feedback: 3 reviews	whoop! __________________ AnimasOutdoor.com Quality Hunting, Fishing, Camping and Outdoor Gear 2007 Wrangler X - Jeep Green, 4" lift, 4.88s, locked rear, custom bumper/fender/cage, rolling on 35s w/ 15s

05-08-2011, 12:25 PM	#83
bnb2010 EZEKIAL 25:17 Join Date: Nov 2010 Member # 12495 Location: Plano, TX Posts: 2,165 Feedback: 0 reviews	I like the calico jack or jolly Roger. Also like the antenna mount Sent from my smoke signals __________________ 2010 Black JKU with enough BDS suspension to clear 37 Goodyears, 4.88, HIDx, Visionx, Wild Boar top. Cobra75, and always ice cold Bryan

05-09-2011, 01:42 PM	#84
BADGER Rock God Join Date: Mar 2009 Member # 3621 Age: 38 Posts: 1,634 Feedback: 0 reviews	Nice product and I like the CB antenna mount. Now, at the risk of being mundane and practical....any chance of a license plate mount or holes for a license plate? __________________ The problem isn't that Johnny can't read. The problem isn't even that Johnny can't think. The problem is that Johnny doesn't know what thinking is; he confuses it with feeling. -Thomas Sowell

05-10-2011, 12:57 PM	#91
Muvovr JKO Addict! Join Date: Jan 2010 Member # 7570 Location: DWG, Texas Posts: 3,115 Feedback: 1 reviews	I am thinking I think he is talking about making the outside perimeter of the decal a plate to achieve the 3-D look over his flat plate design ... ????? __________________ My Parts need Parts.......

05-03-2011, 03:30 PM	#77
JKCobra Beam Me Up Scotty Join Date: Jul 2008 Member # 1624 Posts: 52 Feedback: 0 reviews	Any chance of either a calico jack pirate or the full cobra symbol plate?

05-10-2011, 04:33 PM	#93
yellow rubicon Granite Guru Join Date: Sep 2009 Member # 6294 Location: vineland NJ Age: 39 Posts: 205 Feedback: 0 reviews	Can you do one in stainless stell? 2nd question:how come I can't open your website? 3rd question:are you planing on making a 3rd brake light bracket that attaches to the plate? some advice:you should have the option of a rubber liner that goes between the plate and the tailgate,kind like poison spyder with the side armor that thing saved my body(geniuses) thanks

05-11-2011, 09:51 AM	#95
yellow rubicon Granite Guru Join Date: Sep 2009 Member # 6294 Location: vineland NJ Age: 39 Posts: 205 Feedback: 0 reviews	thanks a lot for the infos,you'll ear from me soon and will be for my order.

05-11-2011, 08:36 PM	#96
DesertSnake JKowners Vendor Join Date: Mar 2011 Member # 14438 Location: Tampa, Florida Posts: 164 Feedback: 1 reviews	Update Quick update For those who will be @ Jeep beach 2011 in Daytona, we will display the final version of the double Jerry can carrier, plus a single jerry can version. Follow the thread here: http://jkowners.com/forum/showthread...071#post774071 CB / Light bracket will be on display as well PS: We will also be introducing our new line JK front and rear bumper prototypes __________________ Desert Snake http://www.DesertSnakeOffroad.com http://www.facebook.com/DesertSnakeOffroad

05-12-2011, 12:19 PM	#97
yellow rubicon Granite Guru Join Date: Sep 2009 Member # 6294 Location: vineland NJ Age: 39 Posts: 205 Feedback: 0 reviews	I would like to see some drawing of your future bumpers,and I think I'm not the only one. pleaaaaase!!

05-12-2011, 06:26 PM	#99
yellow rubicon Granite Guru Join Date: Sep 2009 Member # 6294 Location: vineland NJ Age: 39 Posts: 205 Feedback: 0 reviews	what an honor pictures just for me!! just kidding,very well done!I like them both;about the light bar I'm a steel fabricator(stainless and aluminum)I understand those compound miter on square tubing are bitches. So when the front bumper will be available "just for me",and what the price range is gonna be? and how much is gonna weight+/-? sorry I ask to many questions! THANKS A LOT.

05-12-2011, 08:47 PM	#100
jvandy50 V8 dreams Join Date: Sep 2010 Member # 11593 Location: jonesboro, ar Posts: 2,460 Feedback: 0 reviews	i actually like the name in the rear bumper

Remove Advertisements Sponsored Links
JKOwners.com Advertisement

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode